Part 13

Another good form is “Constantine’s Convoluted Stove” (J. Constantine and Son, 23 Oxford Street, Manchester), Fig. 43. Instead of solid gills, there are a series of perpendicular convolutions which double the heating surface, and the makers’ claim to greater efficiency is no doubt correct. This stove, however, should be classed with hot-air furnaces, as it is not made in small sizes for direct heating; but for warming large buildings, churches, &c., for heating laundry drying-rooms, Turkish baths, &c., it is to be highly recommended.

The German principle, which might advantageously be adopted to a greater extent in England, is to build a fire-brick structure with the furnace at the base and the flue winding from side to side 3 or 4 times, and terminating at the top into an ordinary brick chimney; this structure projects into the apartment and is covered with porcelain ware, and the appearance often exhibits great taste and skill, as it will be understood that the structure is not rigidly square, but is often very beautiful from an architectural point of view. The good effect experienced is that after 3 or 4 hours’ firing, the mass of brickwork becomes thoroughly heated and the fire is permitted to go out; communication with the chimney is stopped by means of a damper, and every confidence can then be placed in the stove giving out abundance of warmth for the remainder of the day, as the brickwork takes hours to become moderately cool, and the whole of the heat it contains must be diffused into the apartment. It will be noticed that a minimum of heat is lost by this arrangement, and the result is very satisfactory from an economical standing; but it has not the cheerful appearance of our open fires, and efficient ventilation is required. This plan can, however, be satisfactorily adopted for halls or cold situations; in the former it has the further advantage in most instances of warming the stairways and landings in the upper part of the house by the ascension of the heated air. Fire-brick stoves are made by Doulton & Co., Lambeth, London, and are finished in their majolica and Doulton ware; it is needless to add, these wares give the stoves a very handsome appearance.

_Hot-air Furnace._--The close stove is really a hot-air furnace, but it is restricted to heating the air in the room. Other hot-air furnaces are designed to obtain a supply of fresh air and heat it before passing it into the room. The heated air from a fireplace is available to the apartment for only about 12 per cent. of the total amount of heat produced; all the rest passes up the chimney. The close stove, on the contrary, utilises 85-90 per cent. of the heat produced, and loses through the smoke-pipe only about as much as the open fireplace saves--10-15 per cent. And herein lies the striking difference between the relative healthiness of the atmosphere heated by a close stove and an open fireplace. The amount of air which hourly passes through a close stove, heated with a brisk fire, is, on an average, equal to only about 1/10 the capacity of the room warmed, and consequently such stove requires, if unaided, 10 hours to effect a change of the atmosphere in every such apartment. Thus stagnant and heated, the air becomes filled with the impurities of respiration and cutaneous transpiration.

Moisture, too, is an important consideration. The atmosphere, whether within doors or without, can only contain a certain proportion of moisture to each cub. ft., and no more, according to temperature. At 80° F. it is capable of containing 5 times as much as at 32° F. Hence, an atmosphere at 32° F., with its requisite supply of moisture, introduced into a confined space and heated up to 80° F., has its capacity for moisture so increased as to dry and wither everything with which it comes in contact; furniture cracks and warps, seams open in the moulding, wainscoting, and doors; plants die; ophthalmia, catarrh, and bronchitis are common family complaints, and consumption is not infrequent. But this condition of house air is not peculiar to stove-heat. It is equally true of any overheated and confined atmosphere. The chief difference is, that warming the air by means of a close stove is more quickly accomplished and more easily kept up than by any other means. Sometimes, by the scorching of dust afloat in the atmosphere, an unpleasant odour is evolved which is erroneously supposed to be a special indication of impurity, caused by the burning air. It is an indication of excessive heat of the stove. But the air cannot be said to burn in any true sense of the word, for it continues to possess its due proportion of elementary constituents. Such is the close stove and its dangers, under the most unfavourable circumstances.

The essentials for healthy stove-heat are brick-lined fire-chamber, ventilating or exhaust-flue for foul air, means for supplying moisture, and provision for fresh-air supply. A brick lining is requisite for the double purpose of preventing overheating, and for retaining heat in the stove. For the supply of moisture the means are simple and easy of control, but often inadequate. An efficient foul-air shaft may be fitted to the commonest of close stoves by simply enclosing the smoke-pipe in a jacket--that is, in a pipe of 2 or 3 in. greater diameter. This should be braced round the smoke-pipe, and left open at the end next the stove. At its entry into the chimney, or in its passage through the roof of a car, as the case may be, a perforated collar should separate it from the smoke-pipe. For stoves with a short horizontal smoke-pipe, passing through a fire-board, the latter should always be raised about 3 in. from the floor. A smoke-pipe thus jacketed, or fire-board so raised at the bottom, affords ample provision for the escape of foul air.

Hot-air furnaces are simply enclosed stoves placed outside the apartments to be warmed, and usually in cellars or basements of the buildings in which they are used. The manner of warming is virtually the same as by indirect steam heat--by the passage of air over the surface of the heated furnace or steam-heated pipes, as the case may be, through flues or pipes provided with registers. The most essential condition of satisfactory warming by a hot-air furnace is a good chimney-draught, which should always be stronger than that of the hot-air pipes through which the warmed air is conveyed into the rooms, and this can be measured by the force with which it passes through the registers. A chimney-draught thus regulated effectively removes all emanations; for, if the chimney-draught exceeds that of the hot-air pipes, all the gaseous emanations from the inside of the furnace, and if it have crevices, or is of cast iron and overheated, all around it on the outside will be drawn into the chimney. Closely connected with this requirement for the chimney-draught is the regulating apparatus for governing the combustion of fuel--the draught of the furnace. This should all be below the grate; there should be no dampers in the smoke-pipe or chimney, and all joints below and about the grate should be air-tight. The fire-pot should be lined with brick and entirely within the surface, but separate from it, so that the fresh air to be warmed cannot come in contact with the fuel-chamber.

An excellent plan for economising a good portion of the waste heat from a kitchen range is to have (previous to the range being fixed, or after, in some instances) a sheet-iron box or chamber made to fit at the back of the oven flues or wherever the most intense heat is felt. This box, which we may call an air-chamber, should be connected with the outer air, and a pipe for the warm air carried from the top of the box to the part where warmth is required; the heat from the range warms the air in the box and it ascends in exactly the same manner and upon the same principle as a hot-air furnace, but great care must be exercised to see that this box and all connections are made air-tight, or this plan will prove an unusually speedy means of indicating what is being cooked for dinner.

The Americans adopt what is called the “drum” principle of heating by means of a furnace; they not only encase the stove with an air-chamber, but the smoke-pipe is surrounded with a larger pipe encasing it all the way up; the space between the smoke-pipe and the outer pipe is thus an air-chamber and has free connection with the furnace air-chamber, but of course is closed at top; from the chamber surrounding the smoke-pipe, branch pipes are taken to the apartments, terminating in perforated cylindrical “drums,” from which the heated air is emitted.

It should go without saying that the air which passes from furnaces into living-rooms should always be taken from out of doors, and be conveyed in perfectly clean air-tight shafts to and around the base of the furnace. Preferably, the inlet of the shaft, or cold-air box, should be carried down and curved at a level (of its upper surface) with the bottom, and full width of the furnace. Thus applied, the air is equally distributed for warming and ascent through the hot-air pipes to the apartments to be warmed. On the outside the cold-air shaft should be turned up several feet from the surface of the ground, and its mouth protected from dust by an air-strainer. A simple but effectual way is to cover the mouth with wire cloth, and over this to lay a piece of loose cotton wadding. This may be kept in place with a weight made of a few crossings of heavy wire, and it should be changed every few months. And here, too, outside the house, should be placed the diaphragm for regulating the amount of cold-air supply, and not, as commonly, in the cellar.

As the best means of regulating the temperature and purity of the atmosphere from hot-air furnaces, it is necessary to provide sufficiently large channels for both the inlet of fresh air and its distribution through the hot-air pipes. The area of the smallest part of the inlet (or inlets, for it is sometimes better to have more than one) should be about ⅙ sq. ft. for every lb. of coal estimated to be burnt hourly in cold weather; and to prevent, in a measure, the inconvenience of one hot-air pipe drawing from another, the collective area of the hot-air pipes should not be more than ⅙ greater than the area of the cold-air inlet. These proportions will admit the hot air at a temperature of about 120° F. when at zero outside, and the velocity through the register will not exceed 5 ft. per second.

A large heating surface of the furnace is a well-recognised condition of both economy and efficiency. As a rule, there should be 10 sq. ft. of heating surface to every lb. of coal consumed per hour, when in active combustion; and the grate area should be about 1/50 of that of the heating surface. For the deficiency of heat, or the failure of some of the hot-air pipes of hot-air furnaces in certain winds and weathers in large houses or specially exposed rooms, the best addendum is an open fire-grate. With this provision in northerly rooms, to be used occasionally, hot-air furnaces may be made to produce all the advantages of steam heat in even the largest dwelling-houses.

Boyle’s system of warming fresh air is suitable where hot air, water, or steam pipes are not available. The arrangement (Fig. 44) consists of a copper or iron pipe _a_ about 1½ in. diam. placed in an inlet tube _b_, preferably of the form of a bracket. This pipe is not vertical, as in the so-called Tobin’s shafts, but of zigzag shape, crossing and recrossing the tube from top to bottom, and so causing the incoming air to repeatedly impinge in its passage through the tube. At the bottom of the tube an air-tight chamber, so far as the interior of the tube is concerned, is fixed, in which a Bunsen gas-burner _c_ is placed, the flame of which plays up into one of the lower ends of the pipe, the upper portion being about 5 ft. 9 in. from the floor. The other lower end of the pipe either dips into a condensation box _d_ in the bottom of the tube or is continued into an existing flue or extraction shaft. If the pipe terminates in a box, the vapour is condensed there and carried off through the outside wall by means of a small pipe. At the bottom of the box is placed some loose charcoal, which needs renewing at intervals. This charcoal absorbs any products of combustion which have a tendency to rise. The heat thus passes through the entire length of the pipe, and warms the air as it travels through the tube to the room or hall as required.

Heating by gas is now growing in favour, and under favourable circumstances is to be recommended. There are two general methods adopted; firstly, by gas fires, which are asbestos or metal made incandescent by gas heat; these are made either portable, or by fitting a specially made burner to an existing fireplace, and filling the grate with Lumb asbestos (which is made for the purpose, and when heated has the appearance of glowing coals); and secondly, by gas stoves acting upon a similar principle to a hot-air coal stove. The former are now made in great variety; they chiefly take the form of an ornamental iron frame, in the centre of which is fitted a fire-brick thickly imbedded in front with asbestos fibre; the burner beneath comes immediately under the front of the fire-brick, and when the gas is ignited, the asbestos at once becomes incandescent, making it of cheerful and fire-like appearance, and the fire-brick in a few minutes becomes highly heated, radiating its warmth into the room. This description of stove and also the burner for existing fireplaces can be obtained at any ironmongers or gas-fitters.

In nearly all gas fires and stoves the gas is burnt with an admixture of air (atmospheric gas, 1 of gas and 2 of air), by means of an atmospheric burner; this is not only a source of economy, but atmospheric gas has the very great advantage of being smokeless; but for this, a gas fire would be an impossibility; it must, however, be borne in mind that although smokeless this gas gives off products of combustion (carbonic acid, watery vapour, &c.), which must be carried away by a flue or other means. The portable stoves are always provided with a nozzle for attaching a smoke-pipe. There is still a doubt as to which is most economical, coal or gas: we cannot do better than quote the words of a well-known gas-stove maker, Chas. Wilson, of Leeds. He says, speaking of heating by gas: “It is not cheaper than coal, taking fuel for fuel and continually used, unless, as in the case of offices where labour has to be employed to light fires, clean grates, &c.; but it is cheaper than coal if occasionally used, as in the case of bedrooms, or sitting-rooms used by visitors, or rooms used by children for music, &c.; for bedrooms it is especially adapted for use for an hour or two at night or in the morning or for giving an unvarying heat all night. It is preferable in the matter of cleanliness, and a true solution of the smoke-abatement problem” (probably a coal-stove manufacturer would speak as much in favour of fire-grates).

It should be seen when purchasing gas fires that they have silent burners, as some make an objectionable hissing noise when in use.

“The Calorigen” Gas Hot-air Stove, Fig. 45 (Farwig & Co., 36 Queen Street, Cheapside, London), consists of an outer sheet-iron casing with a burner at the base inside, and proper accommodation for exit of products of combustion. A coil of good-sized sheet-iron pipe is affixed within the stove; the lower end of the coil is connected with the outer air and the upper end opens into the apartment, thus producing a free inflow of fresh air at any temperature desired, from 60° to 200° F. or higher at will. The chief advantage of a gas stove is the immediate lighting and extinguishing, and needing no attention.

Another modern and very useful application of gas as a heating medium is the “Geyser” or rapid water heater for the supply of hot or boiling water to baths, lavatories, &c., or for business purposes where it is not convenient or desirable to fit up a circulating boiler (see hot-water apparatus). These heaters can be obtained from any ironmonger’s or gasfitter’s. The principle is somewhat different in the various makes, but it all results in the same thing, which is to bring a small volume of water in contact with a large heating surface. The apparatus is generally cylindrical in form. A cock is at one side for attaching the cold supply, and the heated water flows out from a spout at the other side; there is also a cock for attaching the gas supply; they are made in various sizes to supply and fill a bath three parts full of water at 100° F. in 5, 10 or 15 minutes, or to boil water at the rate of ½, 1 or 2 gal. per minute. These are extremely useful appliances where gas is available, being ready for use at a moment’s notice, and the water can be had at any temperature at will; with a modern and properly constructed “Geyser” the water is quite suitable for drinking purposes.

The Marsh-Greenall Gas Heating Stove, Fig. 46 (makers, Greenall and Company, 120 Portland Street, Manchester), is both regenerative and radiating, the heat developed and utilised per foot of gas by this system being far greater than by the ordinary atmospheric stoves. Ordinary luminous flames are used, these being fed by superheated air. There is no smell and no danger “of lighting back.” The great heat obtained by this system is radiated from a polished reflector. The consumption of gas is only 12 ft. per hour. See Gas Heating also, p. 994.

_Oil Stoves._--Warming stoves which burn oil fuel are to be commended for many purposes, but are not generally considered suitable for living rooms--bedrooms, for instance--unless the air is continually changed by open doors, &c., as there is a noticeable odour from the burning oil. Rippengille’s are considered the best, and are obtainable at almost any oil, lamp, or ironmonger’s store, or at the chief retail agents, the Holborn Lamp Co., 118 Holborn, London. Fig. 47 is their “Eureka” cheerful reflector stove, suitable for office or shop use. These stoves are adapted for warming conservatories where a high temperature is not required, as a very small stove will suffice to keep the frost out; they are also suitable for servants’ bedrooms and attics where no fireplaces exist. They are made with metal (unbreakable) oil containers, which slide out for lighting, trimming, &c., and they burn the ordinary petroleum oil; it naturally follows that the better and more refined oils give the best results with these stoves, with less liability of smell.

_Flues._--It will not be out of place to give a short treatise upon flues, as the flues in a residence govern the efficiency of the stoves and the comfort of the whole household.

There is a common error in blaming the flue for all faults. It can be asserted that half the smoky chimneys are in no way the fault of the flue at all, and when a smoky chimney does exist, nearly every one flies to the chimney top with some device to govern the wind, and this in very many cases is a total failure.

Flues are now generally constructed of two sizes, 9 in. and 14 in. A 7 in. flue would be sufficient for most warming stoves, but it has to be borne in mind that the accumulation of soot quickly diminishes the size internally, so that they are now never built less than 9 in. internal diameter. In building a residence, the following plan is often adopted when cheapness is not the primary object, that is, to build the usual square brick chimney, and within this to carry up a 9 in. flue of glazed earthenware pipe (drain pipe), and the space outside this pipe filled with concrete: this pipe flue is so easily cleaned and is much less quickly fouled, and improves the draught.

The very general cause of smoky chimneys is that the chimney top is below the level of some adjacent building, tree, or other object that obstructs the free passage of the wind. In this instance the trouble is only experienced when the wind is in certain quarters, and sometimes this can be cured by a wind-guard or cowl (no particular make can be recommended, as their efficiency differs under different circumstances); but the only reliable remedy is to raise the chimney either by pipe or brickwork to the required height. The manner in which the annoyance is brought about is, that when the wind passes over the chimney top its progress is arrested by the higher object, and it may be said to rebound (the action is rarely quite alike in any two instances), causing either a portion of the gust to pass a short way down the chimney or to momentarily stop the up draught; this will be noticed by the gusts of smoke that come from the stove into the room.

When the smoke slowly oozes into the room, it is caused by sluggish draught, or often by the construction of the grate. If the grate has considerable distance between the fire-bars and the opening into the chimney above, it permits the heavy cold air to accumulate and obstruct the heated up-flow from the fire; this generally is only noticeable when the fire is first lighted or heavily fed. It is exactly the same result as is experienced with the old-fashioned open kitchen ranges, which nearly always require a sheet of metal or “blower” across the opening to prevent their smoking. The above-mentioned grates require a strong draught to work them perfectly; or if a strong draught does not exist, a small piece of sheet-metal should be provided to fit over the open space above the front bars when necessary to establish the fire, as explained with the “Eagle” grate.

Sluggish draughts are from a variety of causes, among which might be named, insufficient height of chimney; chimneys which by any cause may become damp or cold, or lose their heat rapidly; leakages, holes or fissures, and a variety of causes too numerous to mention here. The interior surface of a chimney should be as smooth as possible, and should be swept at regular and moderately frequent intervals, otherwise the draught will be reduced.

Every fireplace should have a distinct and separate flue; sometimes two fireplaces can be successfully worked into one chimney, but provision must be made for tightly closing off either one when not in use.