Part 2
When sweet-clover hay is cut at the right time and cured properly it is eaten readily by all classes of live stock. As the hay is rich in protein, growing stock make gains on it comparable to the gains of those fed on alfalfa. The quantity and quality of the milk produced when the hay is fed to cows are approximately the same as when other legumes are used. Hay which is cut the first year is fine stemmed and leafy and resembles alfalfa in general appearance. Unless it is cut at the proper time the second year, it will be stemmy and unpalatable. Feeding experiments show that it contains practically as much digestible protein as alfalfa and more than red clover, but the hay is not as palatable as red clover or alfalfa when the plants are permitted to become coarse and woody. When sweet clover is seeded in the spring without a nurse crop in the northern and western sections of the United States, a cutting of hay may be obtained the same autumn. When it is seeded with a nurse crop in these regions, the rainfall during the late summer and early fall will largely determine whether the plants will make sufficient growth to be cut for hay. On fertile, well-limed soils in the East, in the eastern North-Central States, in Iowa, and in eastern Kansas a cutting of hay is commonly obtained after grain harvest when the rainfall is normal or above normal. In many sections of the country two, and at times three, cuttings of hay may be obtained the second year (fig. 3).
In the South two, and sometimes three, cuttings may be obtained the first year if the seeding is done without a nurse crop. When the seed is sown in the spring with oats, two cuttings may be secured after oat harvest. Three cuttings may be obtained the second year, although it is the common practice to cut the first crop for hay and the second crop for seed.
YIELDS OF SWEET-CLOVER HAY.
The total yields of sweet clover per acre for the season are usually less than those of alfalfa except in the semiarid unirrigated portions of the country. Sweet clover ordinarily yields more to the acre than any of the true clovers.
When the seed is sown in the spring in the North without a nurse crop, yields of 1 to 3 tons of hay of good quality may be expected the following autumn, The Massachusetts Agricultural Experiment Station obtained 2,700 pounds of hay per acre in the fall from spring seeding, while the United States Department of Agriculture obtained 3,000 pounds of hay per acre in August from May seeding in Maryland. Yields of 1 to 2 tons, and occasionally 3 tons, have been obtained in Michigan, Illinois, Iowa, Kansas, the Dakotas, and other States. In Illinois, Iowa, and Kansas yields of 1 to 1-1/2 tons are often obtained after grain harvest when weather conditions are favorable.
The first crop the second season yields 1-1/2 to 3 tons of hay to the acre in the northern and western sections of the United States. The second crop of the second season will yield from three-fourths to 1-1/2 tons to the acre, although this crop usually is cut for seed.
When sweet clover is seeded in the South without a nurse crop on fairly fertile soil that is not acid, three cuttings of hay, averaging at least a ton to the cutting, may be secured the year of seeding. When the seed is sown in the early spring on winter grain, two cuttings, yielding at least 1 ton to the cutting, may be obtained. The first crop the second season yields on an average 1-1/2 to 3 tons of hay to the acre. In 1903 the Alabama Canebrake Station obtained 2-1/2 tons of hay after oat harvest and a total yield of 3 tons per acre from the same field in 1904.
TIME TO CUT SWEET CLOVER FOR HAY.
The first season's growth of sweet clover does not usually get coarse and woody and therefore may be cut when it shows its maximum growth in the fall, In regions where more than one crop may be obtained the first season, the first crop should be cut when the plants have made about a 30-inch growth.
The proper time to cut the first crop the second season will vary considerably in different localities, depending very much upon the rainfall, the temperature, and the fertility of the soil. In no event should the plants be permitted to show flower buds or to become woody. In the semiarid sections of the country sweet clover does not grow as rapidly as in more humid regions. Neither do the plants grow as rapidly on poor soils as upon fertile soils. In the drier sections the best results usually are obtained by cutting the first crop when the plants have made a growth of 24 to 30 inches. On fertile, well-limed soils in many sections of the country a very rapid growth is made in the spring, and often the plants will not show flower buds until they are about 5 feet high. On such soils it is very essential that the first crop be cut when the plants have made no more growth than 30 to 32 inches if hay is desired which is not stemmy and if a second growth is to be expected.
HEIGHT OF STUBBLE TO BE LEFT WHEN CUTTING FOR HAY.
It is not necessary to leave more than an ordinary stubble when cutting the sweet-clover hay crop in the fall of the year of seeding. A stubble 4 or 6 inches in height, however, will serve to hold drifting snow and undoubtedly will be of some help in protecting the plants from winter injury. While sweet clover without question is more hardy than red clover, usually more or less winterkilling occurs, and any protection which may be afforded during cold weather will be of considerable benefit.
While the first crop in the second year comes from the crown buds, the new branches which produce the second crop of the second year come from the buds formed in the axils of the leaves on the lower portions of the stalks which constitute the first crop, as shown in figure 4. These branches usually commence growth when the plants are about 24 inches high. In fields where the stand is heavy and where the lower portions of the plants are densely shaded, these shoots are soon killed from lack of necessary light. (Figs. 4 and 5.) The branches which are first to appear and which are first to be killed are those closest to the ground. It is therefore very important when cutting this crop to cut the plants high enough from the ground to leave on the stubble a sufficient number of buds and young branches to produce a second crop.
Examination of hundreds of acres of sweet clover in different sections of the United States during the summers of 1915 and 1916 showed that the stand on at least 50 per cent of the fields was partly or entirely killed by cutting the first crop the second season too close to the ground. A direct relation exists between the thickness of the stand, the height of the plants, and the height at which the stubble should be cut if a second crop is to be harvested. It is very essential to examine the fields carefully before mowing, so as to determine the height at which the plants should be cut in order to leave at least one healthy bud or young branch on each stub. In fact, the stand should be cut several inches above the young shoots or buds, the stubble may die back from 1 to 3 inches if the plants are cut during damp or rainy weather.
When fields of sweet clover contain only a medium-heavy stand and when the plants have made no more than a 30-inch growth, a 5 to 6 inch stubble usually will be sufficient to insure a second crop, but where fields contain heavy stands--15 to 25 plants to the square foot--it may be necessary to leave an 8-inch stubble. In many fields examined in northern Illinois in June, 1916, heavy stands had been permitted to make a growth of 36 to 40 inches before cutting. In a number of these fields a very large percentage of the plants were killed when an 8 to 12 inch stubble was left. (See fig. 5.) A careful examination of such fields showed that the young branches had started on the lower portions of the stalks and had died from lack of light before cutting. In semiarid regions, where the plants do not make as rapid growth as in humid sections, they may, as a rule, be clipped somewhat closer to the ground without injury.
On account of the difference in the growth that sweet clover makes on different types of soil and on account of the difference in the thickness of the stand obtained in different fields, it is impossible to give any definite rule as to the proper height to cut the first crop.
MOWER CHANGES FOR CUTTING SWEET CLOVER.
It is good practice to replace the shoe soles of the mower with higher adjustable soles, so that a stubble up to 12 inches in height may be left when cutting sweet clover, Shoe soles such as are shown in figures 6 and 7 may be made on any farm provided with a blacksmith's forge, or they can be made at any blacksmith shop at a cost which should not exceed $2.50. Preferably they should be of strap iron, about one-fourth of an inch thick and 2 inches wide; however, old pieces of iron or steel which may be found on the farm will serve the purpose.
Then these soles are to be placed on machines that have shoes of the type used on the Deering mower, the forward 8 inches of the sole for the inner shoe should be tapered gradually to a blunt point and bent in such a manner that it will hook into the slot in the shoe. (Fig. 6, _C_.) When the soles are to be placed on mowers having shoes of the type used on McCormick machines, the forward 8 inches of the sole for the inner shoe should be tapered gradually to about 1 inch in width, bent forward so that it will fit against that portion of the shoe where it is to be bolted, and have a hole of the proper size bored for the bolt three-fourths of an inch from the end. (Fig. 6, _B_ and _D_.) The bottom of the sole should be rounded, so as to run smoothly on the ground when the cutter bar is raised to cut at different heights. The back portion of the sole should be upright and should have holes bored in it, so that it may be set for the cutter bar to rest at different heights from the ground. Preferably the lower hole of the upright should be located so that when the bolt in the shoe is run through it the cutter bar will be 6 inches from the ground. It should be long enough to permit four or five holes, 1 inch apart, to be bored above the lower one. (Fig. 6, _A_.)
With some makes of machines it is not advisable to raise the cutter bar higher than 10 inches from the ground, but when this is true the cutter bar may be tipped upward, so that a 12-inch stubble is left.
The forward end of the shoe sole to be used on the outer shoe should be tapered gradually to 1 inch from the end. The forward inch should be one-fourth of an inch in width and bent slightly upward and inward, so that a hook will be formed to fit into the slot in the front end of the shoe. (Fig. 7, _B_.) The rest of the sole should curved, so that it will run smoothly on the ground when the cutter bar is set to cut at different heights. The upright which is bolted to the sole should preferably be made of three-eighths by 1 inch material and should have six holes, 1 inch apart, bored in it, so that the outer end of the cutter bar may be raised to the same height as the inner end. On practically all standard makes of mowers the outer shoe sole hooks into the shoe instead of bolting to it, as is the case with the inner sole on some machines. A wheel is used in place of a shoe sole on the outer end of the cutter bar on some machines. When this is the case, the upright to which this wheel is attached should be lengthened. On other machines the forward end of the sole hooks into a slot in the shoe in the same manner as the inner sole. In this event the front end of the sole should be bent slightly upward and outward. (Fig. 7, _C_.)
Before shoe soles are made for any mower a careful examination should be made of the shoes to determine the exact size required and the manner in which they should be attached to the forward ends of the shoes.
CURING AND HANDLING SWEET-CLOVER HAY.
One of the greatest difficulties in curing sweet clover is the fact that the plants usually are ready to be cut for hay at a time of the year when weather conditions are likely to be unfavorable for haymaking. Little trouble is experienced in curing this crop in the drier sections of the country where the methods used for alfalfa are employed. The curing of sweet clover is more difficult than the curing of either red clover or alfalfa, as the leaves are very apt to shatter before the stems are cured. Every possible means should be employed to save the leaves, as these constitute the best part of the hay. (See Table II.)
Table II.--Average analyses of the leaves of four samples of well-cured white sweet-clover hay.
[Analyses made by the Bureau of Chemistry.]
+------------------------------------------------------------- | Constituents (per cent). +----------+-------+---------+---------+-------+-------------- Samples.| Moisture.| Ash. | Ether | Protein.| Crude | Nitrogen-free | | | extract.| | fiber.| extract. --------+----------+-------+---------+---------+-------+-------------- | | | | | | Leaves. | 8.70 | 10.92 | 3.09 | 28.20 | 9.28 | 39.78 Stems. | 8.70 | 8.08 | .70 | 10.16 | 39.45 | 33.06 | | | | | | --------+----------+-------+---------+---------+-------+--------------
The hay collected for the above analyses represented the first cutting the second season. The plants had made a 30 to 36 inch growth at the time of cutting. It will be seen that the protein content of the leaves is almost three times as great as that of the stems.
In the drier sections of the country or when the first crop of the year of seeding is cut for hay in the North-Central States the mower may be started in the morning as soon as the dew is off. The hay should remain in the swath until the following day, or until it is well wilted, when it should be raked into small windrows. After remaining in the windrows for a day it may be placed in small cocks to cure. Cocks made from hay which has dried to this stage will not shed water well and therefore should be covered if it is likely to rain. It is important that the cocks be made small enough to be thrown on the rack entire, as many leaves will be lost if it is necessary to tear them apart.
When sweet clover is permitted to dry in the swath, a large percentage of the leaves will be lost in windrowing and loading unless handled with the utmost care. Hay in this condition should never be raked while perfectly dry and brittle, but should be raked into the windrow in the early morning or in the evening, when it is slightly damp from dew. It may then be hauled to the barn or stack after remaining in the windrow for a day.
One of the most successful methods for handling sweet-clover hay, especially in regions where rains are likely to occur at haying time, is to permit the plants to remain in the swath until they are well wilted or just before the leaves begin to cure. The hay should then be raked into windrows and cocked at once (fig. 8). The cocks should be made as high and as narrow as possible, as this will permit better ventilation. In curing, the cocks will shrink from one-third to one-half of their original size. It may take from 10 days to 2 weeks to cure sweet clover by this method, but when well cured all the leaves will be intact and the hay will have an excellent color and aroma. When sweet clover is cocked at this time the leaves will cure flat and in such a manner that the cocks will readily shed water during heavy rains (fig. 9).
When sweet-clover hay is to be stacked it is highly desirable that some sort of foundation be made for the stack, so as to prevent the loss of the hay which otherwise would be on the ground. Several feet of straw or grass are often used for this purpose, but still better is a foundation of rails, posts, or boards placed in such a manner that air may circulate under the stack.
A cover should be provided for the stacks, either in the form of a roof, a canvas, or long green grass. If none of these means is practicable a topping of perfectly green sweet clover will cure with the leaves flat and will turn water nicely.
It is well known that hay made from either red clover or alfalfa will often undergo spontaneous combustion if put into the barn with too much external moisture upon it. No instances of spontaneous combustion in sweet-clover hay have been noted, but this may be due to the fact that comparatively little sweet-clover hay is stored in barns. The same precautions, therefore, should be taken with sweet-clover hay as with red clover or alfalfa.
SWEET CLOVER AS A SILAGE CROP.
In some sections of the country sweet clover is gaining in favor as a silage crop, either alone or in mixtures with other plants. The silage made from this plant will keep better than that made from most legumes, as it does not become slimy, as is so often the case with red clover or alfalfa silage. It produces a palatable feed, which should contain more protein than well-matured corn silage.
When sweet clover makes sufficient growth after grain harvest, or when seeded alone, it is not necessary to cut it for silage until fall. At this time it may be run into the silo alone or in mixture with corn. Excellent results have been obtained by placing alternate loads of corn and sweet clover in the silo. (Fig. 10.)
When the first crop the second season is not needed for pasturage, ensiling may prove to be the most economical and profitable way of handling it, as it is necessary to cut this crop for hay at a time of the year when the weather conditions in humid regions are very likely to be unfavorable for haymaking. The large percentage of leaves which usually are lost from shattering when harvesting the hay will be saved when the crop is run into the silo.
The first crop the second season will produce approximately two-thirds as much silage to the acre as corn when it is cut at the time it should be cut for hay. The second crop may then be harvested for seed. When sweet clover is handled in this manner, approximately two-thirds of the total corn acreage which would be cut for silage may be permitted to mature, as the first crop of sweet clover will replace the corn silage, while the seed crop ordinarily will bring as much per acre as the corn. In addition to this, the roots and stubble will add large quantities of vegetable matter to the soil.
Some farmers do not cut sweet clover for silage until it is in full bloom. When this is done, 10 to 12 tons of silage will be obtained per acre, but the plants will be killed by the mowing.
When the green plants are ensiled, the crop preferably should be cut with a grain binder. (See illustration on title-page and fig. 11.) This will solve the difficulty of cutting a high stubble and will at the same time bind the plants so that they may be run through the silage cutter without difficulty. Green plants, and especially the first crop of the second season, contain too much moisture to be run into the silo immediately after cutting. In some cases quantities of juice have been pressed out of the bottom of the silo, and as a result the silage settled considerably. Analyses of the juice from one silo showed that it contained 0.23 per cent protein and 2 per cent carbohydrates. This loss of juice may be overcome by permitting the bundles to remain in the field just as they come from the binder until the plants are wilted thoroughly. Straw or corn stover may be placed in the bottom of the silo to absorb some of the juice. If the plants contain too much moisture it may be a good plan to mix some corn stover with the sweet clover as it is run into the silo.
Several silos in Illinois have been filled with sweet-clover straw. When this is done it is necessary to add sufficient water to moisten the dry stems. These stems become soft in a short time and ensile in good condition. When the seed crop is thrashed with either a grain separator or a clover huller the stems are broken and crushed sufficiently to render it unnecessary to run them through a silage cutter. Care must be taken when ensiling the straw to add sufficient water, if molding is to be avoided. It will probably be necessary to add water at the blower and also at the top of the silo. It is essential to tramp the straw thoroughly, so as to exclude as much air as possible. After the silo is filled it should be covered with a layer of green plants and thoroughly soaked with water.
Table III gives analyses of several sample of sweet-clover silage as compared to corn silage.
Table III.--_Composition of sweet-clover silage and well-matured corn silage._