Part 3

To further strengthen the chassis a strip of flat steel wire sufficiently long enough should be bent so that ¹⁄₂″ of the central portion can be securely fastened to the center of the cross brace as shown in diagram 10. The two outer ends should be bent down and are fastened to the wires which are attached to the bottom ends of the struts. This method of attaching the forward pontoons enables the constructor to adjust them to any desired angle and also detach them when not in use.

A model hydroaëroplane is one of the most interesting types of models and if properly taken care of will afford the constructor many pleasant moments.

LAUNCHING AN R. O. G. OR MODEL HYDROAËROPLANE

Although the method of determining the balance of an R. O. G. or a model hydroaëroplane is exactly the same as that of a hand launched model, the manner of launching is somewhat different. Instead of holding the model one hand in the center of the frame and the other at the rear as in the case of the hand launched model, in launching an R. O. G. or hydro, the model should be rested upon the ground or water, as the case may be, with both hands holding tightly to the propellers. Then when about to let the model go release both propellers instantly. If the model has sufficient power and it has been properly adjusted it will glide over the surface of the ground or water for a short distance, then rise into the air. Should the model fail to rise into the air additional strands of rubber should be added, after which it should be rewound and a second attempt made.

Should the model fail to respond after the addition of extra rubber, the indications are that something requires further adjustment. Perhaps the pontoons need further elevation if the model is a hydro, or if it be an R. O. G. model the forward wing may require an increase of elevation. In any event the model should be carefully examined and adjustments made where necessary, after which the model should be tested for balance and elevation. If satisfied with the behavior of the model after test flights have been made, another attempt should be made to launch the model from the ground or water.

On no account try to fly the model in the house, or see, supposing the model is of the R. O. G. type, if it will rise from the dining room floor. This advice may seem unnecessary, but it is not so, for there has been quite a number of instances in which the above has been done, nearly always with disastrous results, not always to the model, more often to something of much greater value. The smashing of windows has often resulted from such attempts, but generally speaking pictures are the worst sufferers. It is equally unwise to attempt to fly the model in a garden in which there are numerous obstructions, such as trees and so forth. A wrecked model is very often the result of such experimenting. The safest way to determine the flying ability of any model is to take it out in an open field where its flight is less apt to be interrupted.

WORLD RECORD MODELS

THE LAUDER DISTANCE AND DURATION MODEL

After many months of experimentation Mr. Wallace A. Lauder succeeded in producing a model that proved to be one of his most successful models. But a few years ago flights of 1000 feet with a duration of 60 seconds were considered remarkable. But so rapid has been the development of the rubber strand driven model that to-day it is hardly considered worth while to measure a flight of 1000 feet, especially in contests where models fly over 2500 feet or 3537 feet which was the distance flown by Mr. Lauder’s model during one of the contests of the National Model Aëroplane competition of 1915. Mr. Lauder’s model on several occasions made flights of over 3500 feet with a duration in each event of over 195 seconds. It is therefore to be remembered that this model is both a distance and duration model, both qualities being seldom found in one model.

Reference to the accompanying drawing will give a clear idea of the constructional details.

The frame or fuselage consists of two side members 40″ in length, of straight grained spruce. At the center each member is of approximately circular cross section, and is ¹⁄₄″ in diameter. The members taper to about ³⁄₁₆″ at the ends, the circular cross section being maintained throughout. The frame is braced by a strip of bamboo of streamline form, extending from one side member to the other, 18″ from the apex of the frame. The ends of this frame are bent to run parallel to the side members of the frame where they are secured by binding with silk thread and gluing. Piano wire hooks are also secured to the side members of the frame adjacent the ends of the cross brace, and from these hooks extend wires of steel (No. 2 music wire) which run diagonally to the rear brace or propeller spar where they are secured.

The frame is braced further by an upwardly arched strip of bamboo, as shown in diagram 11, this strip being 2¹⁄₂″ in height. At the top of this brace are two bronze strips of No. 32 gauge brass, one above the other, one on top of the brace and the other below.

Adjacent the ends of these strips of metal are perforations through which pass bracing wires, one of which wires runs to the front of the frame where a hook is mounted for its reception, and the other two wires extend to the rear of the frame where they are secured to the propeller brace. The propeller brace consists of a strip of streamlined spruce 11³⁄₄″ in length, the propellers being at an angle, thus clearance is allowed ¹⁄₄″ wide at the center, tapering to ³⁄₁₆″ at the ends. The ends of the propeller brace extend out one inch from the side members of the frame, to allow room for the rubber strands to be used as motive power. In order to avoid slotting the ends of the side members of the frame so that the propeller brace can be secured therein, thin strips of bamboo are secured above and below the end of each side member, by binding with silk thread and gluing, the space between these bamboo strips being utilized for the brace which is securely bound and glued therein. The propeller bearings consist of strips of very thin bronze (No. 32 gauge), about ³⁄₁₆″ in width, bent over ⁵⁄₈″ strips of German silver tubing, the tubing being soldered to the bronze strips and the propeller brace, which fits between the upper and lower portions of the bronze strips, is securely bound and glued thereto.

The propellers are cut from solid blocks of pine, and are 12″ in diameter. The blade, at its widest portion, measures 1³⁄₈″. The blades are cut very thin, and in order to save weight, they are not shellacked or painted.

The propeller shafts are of piano wire (No. 20 size) to fit the tubing used in the bearings, pass through the propellers and are bent over on the outer side to prevent turning. A few small bronze washers are interposed between the propellers and the outer ends of the tubing to minimize friction when the propellers are revolving. Twelve strands of rubber are used for each propeller, the rubber being ¹⁄₈″ flat.

The wings are both double surfaced, and are of the swept back type. The span of the main wing is 28¹⁄₂″, with a chord of 6¹⁄₂″. The elevator has a span of 15″ with a chord of 4³⁄₄″. The main wing has eleven double ribs, these ribs being built up on mean beams of spruce ¹⁄₁₆″ × ³⁄₁₆″, the front beam being placed 1¹⁄₄″ from the entering edge, and the second beam being 2″ back from the front beam. The entering and trailing edges are formed from a single strip of thin split bamboo, all the joints being made by binding with thin silk and gluing.

The elevator is constructed in like manner, except that it only has seven ribs, and the measurements are as above set forth. Both planes are covered with goldbeater’s skin, sometimes known as “Zephyr” skin, which is first glued in place and then steamed, which tightens the same on the plane, and given a coat of preparation used for this purpose.

THE HITTLE WORLD RECORD MODEL

(SINGLE TRACTOR MONOPLANE, 116 seconds DURATION RISING FROM WATER)

The Hittle World record model hydroaëroplane, designed and constructed by Mr. Lindsay Hittle of the Illinois Model Aëro Club, is perhaps one of the most interesting types of models yet produced. The establishing of this record illustrates the value of careful designing and construction and offers to the beginner an example which might be followed if good results are sought. In having broken the world’s model hydroaëroplane record with a tractor type model Mr. Hittle accomplished a feat of twofold importance. First, in having advanced the possibilities of the tractor model, and, second, in illustrating the value of scientific construction. The previous record for this type of model has been but 29 seconds, just one-fourth of the duration made by Mr. Hittle’s model.

Mr. Hittle’s model shows many new and original features not hitherto combined on any one model. Note diagram 12. The model is of extremely light weight, weighing complete but 1.75 ounces. The floats and their attachments have been so designed as to offer the least possible wind resistance. In fact every possible method was utilized in order to cut down weight and resistance on every part of the model. As a result of this doing away with resistance an excellent gliding ratio of 8³⁄₄ to 1 has been obtained.

For the motor base of the model a single stick of white pine ⁵⁄₆″ deep and 45″ in length is used. On the front end the bearing for the propeller is bound with silk thread and a waterproof glue of the constructor’s own composition being used to hold it secure. For the bearing a small light weight forging somewhat in the shape of the letter “L” is used, this being made streamline. At the rear end of the engine base is attached a piano wire hook for the rubber. The stabilizer consisting of a segment of a circle measuring 12″ × 8″ is attached to the under side of the engine base. The rudder measuring 3¹⁄₂″ × 3¹⁄₂″ is attached to the stabilizer at the rear of the engine base.

The wing is built up of two beams of white pine with ribs and tips of bamboo and has an area of 215 square inches.

The wing which has a total span of 43″ and a chord of 5¹⁄₈″ is built up of two beams of white pine with ribs and tips of bamboo and has a total area of 215 square inches. The wing is given a small dihedral and the wing tips are slightly upturned at the rear.

The trailing edge is longer than the entering edge the ribs being placed somewhat oblique in order to secure an even spacing. The wing is attached to the frame by two small bamboo clips which hold it rigidly and permit easy adjustment and is set at an angle of about 4 degrees with the line of thrust.

Both the floats which take practically the whole weight of the machine are situated directly under the wing just far enough behind the center of gravity to prevent the model from tipping backward. These floats are attached to the engine base by means of streamlined bamboo struts. Bamboo is also used in the construction of the float frames. A single float of triangular sections is situated just behind the propeller. The entire weight of the floats and their attachments is but .23 ounces.

The propeller which consists of four blades is built up of two propellers joined together at the hubs and securely glued, the completed propeller having a diameter of 10″ with a theoretical pitch of 14″. The blades are fairly narrow, tapering almost to a point at the tips. The propeller is driven by five strands of ³⁄₁₆th″ strip rubber at about 760 r.p.m. when the model is in flight. At the time when the model made its record flight of 116 seconds the rubber was given 1500 turns which is not the maximum number of turns. At other times the model has flown satisfactorily with less turns of the rubber. While in the air the model flies very slow and stable notwithstanding its light weight and large surface. On three occasions the model has made durations of approximately 90 seconds which rather dispenses the possibility of its being termed a freak.

THE LA TOUR FLYING BOAT

One of the most notable results of the National Model Aëroplane Competition of 1915 was the establishing of a new world’s record for flying boats. Considering that the model flying boat is a difficult type of model to construct and fly, the establishing of this new world record of 43 seconds is remarkable. Credit for this performance is due Mr. Robert La Tour of the Pacific Northwest Model Aëro Club, who designed, constructed and flew the model flying boat which is herewith described and illustrated. Diagram 13.

The frame is made of laminated spruce 40″ in length, made of two strips glued together. They are ³⁄₈″ × ¹⁄₈″ at the center tapering to ³⁄₁₆″ × ¹⁄₈″ at the ends. The cross braces are of split bamboo and are fastened to the frame side members by bringing them to a wedge at the ends and then inserting them into slots in the sides of the frame side members and are finally drilled and bound to the latter. The rear brace is of streamlined spruce ¹⁄₄″ × ¹⁄₈″; this butts against the frame side members and is bound to them. The propeller accommodations are made of brass.

The propellers are 10″ in diameter with a 19″ pitch. These are carved from a block of Alaska cedar 1¹⁄₄″ wide by ³⁄₄″ thick. Of course the propellers may also be made from white pine. To turn the propellers 15 strands of ¹⁄₈″ flat rubber are used.

Bamboo about ¹⁄₁₆″ square is used to obtain the outline of the wings. The main wing has a span of 33″ with a chord of 5¹⁄₂″. Split bamboo is used for the making of the 9 ribs. The wing spar or brace is of spruce ³⁄₁₆″ × ¹⁄₈″ and is fastened below the ribs as illustrated in diagram 13. The elevator is constructed in like manner but has a span of only 17″ × 4³⁄₄″ and has only 5 ribs. A block ³⁄₄″ high is used for elevation. Both wings have a camber of ¹⁄₂″ and are covered on the upper side with silk doped with a special varnish and a few coats of white shellac.

The boat is 20″ long, 3″ in width and shaped as shown. The slip is ¹⁄₂″ deep and is located 7″ from the bow. The rear end is brought down steeply to avoid the drag of the water on this point when the boat is leaving the surface of the water. Spruce ³⁄₆₄ths of an inch thick is used for the making of the sides, but the cross bracing is of slightly heavier material, there being six braces used throughout. The rear brace is much heavier in order to withstand the pull of the covering and to receive the ends of the wire connections. The outriggers or balancing pontoons are constructed of the same material as that of the boat and are held together by a spruce beam 18″ long, ¹⁄₂″ wide by ³⁄₁₆″ thick, streamlined. This beam is fastened to the boat by means of three brads to permit changing if necessary. The lower edges of the outriggers should clear the water about ¹⁄₈″ before the steps on the boat leave the water. The boat and outriggers are covered with silk, shrunk with a special solution and then coated several times with white shellac. It is a good plan to shellac the interior walls of the boat and pontoons before covering to prevent them from losing their form by becoming soft from the influence of water in the case of a puncture.

The boat is connected to the frame at its front by two steel wires, their ends being inserted into the cross members of the boat, and then brought up along the sides, crossed and then bound to the frame. A similar pair of connecting wires are used to connect the rear end of the boat to the rear end of the frame. A U-shaped wire is bound to the outrigger beam and frame. A single diagonal strip of bamboo is also fastened to the outrigger beam with a brad, its upper end being bound to the cross bracing of the frame, making a very solid connection.

Under ideal weather conditions this model will fly on 12 strands of rubber with the possibility of a better duration than has been made. But, however, with 15 strands the model will rise at every attempt. More rubber, however, causes the bow of the boat to nose under and to accommodate this increase of power the boat should be lengthened.

THE COOK NO. 42 WORLD RECORD MODEL

(TWIN PROPELLER HYDROAËROPLANE, 100.6 SECONDS RISING FROM WATER)

During the National Model Aëroplane Competition of 1915 held under the auspices of the Aëro Club of America, a number of new world records were established, one of which was for twin propeller hydroaëroplanes. The credit for this record is due Mr. Ellis C. Cook of the Illinois Model Aëro Club, who succeeded in getting his model hydroaëroplane—which by the way is a rather difficult type of model to operate—to rise from the water and remain in the air for a duration of 100.6 seconds. This model is of the common A frame design with the floats or pontoons arranged in the familiar fashion, two forward and one aft. The model is fairly light, weighing, when complete, 3.33 ounces, ¹⁄₂ ounce of which is made up in rubber strands for motive power. Diagram 14.

The frame is made of two sticks of white pine for side members, each member measuring 38¹⁄₄″ in length, ⁵⁄₁₆″ in depth, by ¹⁄₈″ in width. These are cut to taper toward the ends where they are only ¹⁄₈″ in width by ³⁄₁₆″ in depth in the front and rear respectively. Three “X” strips of streamlined bamboo measuring ³⁄₁₆″ in width by ³⁄₆₄ths of an inch in depth, are used for bracing the frame between the front and rear and are arranged as shown in diagram 14. The propeller bearings are of small streamlined forgings of light weight, and are bound to the rear end of each side member first by gluing, then binding around with thread. The front hook is made of No. 16 piano wire and is bound to the frame as shown in diagram 14. The chassis which holds the floats or pontoons is made of ³⁄₃₂″ bamboo bent to shape and bound to the frame members. By the use of rubber strands the floats are attached to the chassis; the forward ones being attached so that angle may be adjusted.

The main wing has a span of 36″ and a chord of 5″ and is constructed of two white pine beams each 39″ long, with bamboo wing tips. The ribs, seven in number, are also made of bamboo and are spaced along the edges of the wing at a distance of 4¹⁄₂″ apart. The “elevator” or front wing has a span of 14″ and a chord of 3¹⁄₄″, the framework of which is made entirely of bamboo. The entering edge of this wing is given a slightly greater dihedral so that the angle of incidence at the tips is greater than at the center. By this method the added incidence in the front wing is obtained. By the use of rubber bands both wings are attached to the frame.

The two forward floats are spaced eight inches apart and are of the stepped type, the step being 3¹⁄₂″ from the front and has a depth of ¹⁄₈″. These two floats are separated by two bamboo strips as shown in the diagram, which are tied to the rounded portion of the under carriage by small rubber bands. By the sliding of these strips back and forth the necessary angle of the floats may be obtained to suit conditions. The floats are built up with two thin pieces of white pine for sides, separated by small pieces of wood about one-half the size of a match in cross section. Chiffon veiling which is used for the covering of the wings, is also used for the covering of the floats, after which it is covered with a special preparation to render both the wings and the floats air and water-tight.

The two ten-inch propellers with which the model is fitted have a theoretical pitch of twelve and one-half inches. The propellers are carved from blanks one-half inch thick, the blades of the completed propellers having a maximum width of one inch at a radius of three inches. The propeller shafts are made from No. 16 piano wire and have small washers for bearings. Each propeller is driven by three strands of ¹⁄₄″ strip elastic. The rubber is given 1700 to 1750 turns and revolves the propellers at 1150–1200 r.p.m., when the model is in flight.

The model usually runs over the surface of the water for a distance of from two to three feet before it rises, after which it climbs at a very steep angle to the necessary altitude. The model seems, when in flight, to be slightly overpowered but this is misleading. The rubbers usually unwind in from 85 to 90 seconds. On four out of six flights this model has made a duration of between 98 and 100 seconds which is rather unusual for a model of this type.

THE RUDY FUNK DURATION MODEL

Of the many different types of duration models that have made their appearance during the year of 1915 perhaps the model described herewith, constructed and flown by Mr. Rudolph Funk, of the Aëro Science Club, was one of the most successful. Unlike most models the propellers of this model are bent and not cut. This model made its appearance during the latter part of 1915, on several occasions having flown for over 100 seconds duration. Diagram 15.

While retaining the important characteristics of his standard model, slight changes have been made. Instead of the usual wire for the construction of the frame of the wings, bamboo is used in its place for lightness and strength. The wing frames are single surfaced, China silk being used for covering. The “dope” which is used to render the silk airtight is made by dissolving celluloid in banana oil. This in turn is applied to the silk with a soft brush.

The camber of the main wing is ³⁄₄″ at the center, with a slight reduction towards the negative tips; it also has a dihedral angle of 2 degrees. The main beam, which is secured to the under side of the frame for rigidness, is of spruce 1″ by ⁵⁄₆₄″, tapering to ³⁄₄″ × ⁵⁄₆₄″. The ribs for the main wing and small wing or “elevator” are cut from solid pieces of bamboo ³⁄₁₆″ thick by ¹⁄₄″ wide. These pieces of bamboo are first bent to the proper camber and are then cut into strips each ¹⁄₁₆″ wide. The ribs are next tapered to a V at the bottom, toward the trailing edge, as shown in diagram 15, and also toward the entering edge. To accommodate the entering and trailing edges of the frame, each rib is slit slightly at both ends. Both edges of the frame are then inserted in the slots at the ends of the ribs and bound around with silk thread.

The frame is composed of two sticks of silver spruce 38″ in length, ⁵⁄₁₆″ × ³⁄₁₆″, tapering to ¹⁄₄″ × ⁵⁄₃₂″, held apart by a streamline bamboo cross brace in the center. An additional brace of bamboo is securely fastened across the frame toward the front. The propeller brace consists of a streamline-cut piece of bamboo 12¹⁄₂″ in length by ³⁄₈″ in width at the center, tapering to ¹⁄₄″ toward the ends. The propeller brace is inserted in slots cut in the rear ends of the frame members, then bound and glued.