Part 12
This piece is represented by fig 56. Let A, be a strong decagon wheel, two feet six inches diameter; then on each side of it fix a cone B and C; these cones are to consist of a number of hoops, supported by three or four pieces of wood, in the manner of the spiral wheels; let the height of each cone be three feet six inches, and on all the hoops tie port fires horizontally, with their mouths outwards, and cloath the wheel with eight ounce cases, all to play horizontally, two at a time: the cones may be fired with the first or second cases. The spindle for this piece must go through both the cones, and rise three feet above the point of the cone at top, so that its length will be ten feet four inches from the top of the post H, in which it is fixed, allowing four inches for the thickness of the block of the wheel; the whole weight of the wheel and cones must bear on a shoulder in the spindle, on which the block of the wheel must turn; near the top of the spindle, must be a hole in the front, into which screw a small spindle, after the cones are on; then on this small spindle fix a sun D, composed of sixteen nine inch four ounce cases of brilliant fire, which cases must not be placed on a fell, but only stuck into a block of six inches diameter; then in the front of this sun must be a circular vertical wheel, sixteen inches diameter; on the front of this wheel form with iron wire a spiral line, and cloath it with illuminations, after the usual method; as this wheel is not to be fired till the cones are burnt out, the method of firing it is as follows; let the hole in the block, at the top of the uppermost cone, be a little larger than the spindle which passes through it; then from the first case of the vertical wheel before the sun, carry a leader down the side of the spindle to the top of the block of the horizontal wheel, on which must be a tin barrel; then this leader, being met by another brought from the end of the last case of the horizontal wheel, will give fire to the vertical wheel, as soon as the cones are extinguished; but the sun D must not be fired, till the vertical wheel is quite burnt out.
Of Fire Pumps.
Cases for fire pumps, are made in the same manner as those for tourbillons, only they are parted instead of being rolled dry. Having rolled and dryed your cases, fill them in the following manner: first put in a little meal powder, and then a star, on which ram lightly a ladle or two of composition, then a little meal powder, and on that a star, then again composition, and so on till you have filled the case. Stars for fire pumps should not be round, but must be made either square, or flat and circular, with a hole through the middle; the quantity of powder for throwing the stars must increase as you come near the top of the case, for if much powder be put at the bottom, it will burst the case. The stars must differ in size, in this manner; let the star which you put in first, be about one fourth less than the bore of the case, but let the next star be a little larger, and the third star a little larger than the second, and so on; let them increase in diameter, till within two of the top of the case, which two must fit in tight. As the loading of fire pumps is somewhat difficult, it will be necessary to make two or three trials, before you depend on their performance: when you fill a number of pumps, take care not to put in each an equal quantity of charge between the stars, so that when they are fired they may not throw up too many stars together. Cases for fire pumps should be made very strong, and rolled on four or eight ounce formers, ten or twelve inches in length each.
Of the Vertical Scroll Wheel.
This wheel may be made of any diameter, but must be constructed as shewn by fig. 57, to do which proceed thus; have a block made of a moderate size, into which fix four flat spokes, and on them fix a flat circular fell of wood; round the front of this fell place port-fires; then on the front of the spokes form a scrole, either with a hoop or strong iron wire; on this scrole tie cases of brilliant fire, in proportion to the wheel, head to tail, as in the figure; when you fire this wheel, light the first case near the fell; then, as the cases fire successively, you will see the circle of fire gradually diminish; but whether the illuminations on the fell begin with the scrole or not, is immaterial, that being left intirely to the maker.
N. B. This wheel may be put in the front of a regulated piece, or fired by itself, occasionally.
Of Pin Wheels.
First roll some paper pipes, about fourteen inches in length each; these pipes must not be made thick of paper, two or three rounds of elephant paper being sufficient; when your pipes are thoroughly dryed, you must have made a tin tube, twelve inches in length, to fit easy into the pipes; at one end of this tube fix a small conical cup, which being done, it is called a funnel, then bend one end of one of the pipes, and put the funnel in at the other, as far as it will reach, and fill the cup with composition; then draw out the funnel by a little at a time, shaking it up and down, and it will fill the pipe as it comes out; having filled some pipes, have made some small blocks, about an inch diameter, and half an inch in thickness; round one of these blocks wind and paste a pipe, and to the end of this pipe join another, which must be done by twisting the end of one pipe to a point, and putting it into the end of the other, with a little paste; in this manner join four or five pipes, winding them one upon the other, so as to form a spiral line; having wound on your pipes, paste two slips of paper across them, to hold them together; besides these slips of paper, the pipes must be pasted together.
There is another method of making these wheels, called the French method; which is, by winding on the pipes without paste, and sticking them together with sealing wax, at every half turn; so that when they are fired, the end will fall loose every time the fire passes the wax, by which means the circle of fire will be considerably increased. The formers for these pipes are made from one and a half to four sixteenths of an inch diameter, and the composition for them as follows; meal powder eight ounces, salt petre two ounces, and sulphur one; among these ingredients, may be mixed a little steel-filings, or the dust of cast-iron; this composition should be very dry, and not made too fine, or it will stick in the funnel. These wheels may be fired on a large pin, and held in the hand with safety.
Of Fire Globes.
There are two sorts of fire globes, one with projected cases, and the other with the cases concealed in the following manner; have a globe made of wood, of any diameter you chuse, and divide the surface of it into fourteen equal parts, and at each division bore a hole perpendicular to the center; these holes must be in proportion to the cases intended to be used; in every hole, except one, put a case filled with brilliant, or any other charge, and let the mouths of the cases be even with the surface of the globe; then cut in the globe a groove, from the mouth of one case to the other, for leaders, which must be carried from case to case, so that they may all be fired together; this being done, cover the globe with a single paper, and paint it. These sort of globes may be used to ornament a building.
Fire-globes with projected cases are made thus; your globe being made with fourteen holes bored in it as usual, six in every hole, except one, a case, and let each case project from the globe two thirds of its length; then cloath all the cases with leaders, so that they may all take fire at the same time. Fire-globes are supported by a pintle, made to fit the hole in which there is no case.
To thread and join Leaders, with the method of placing them on different Works.
Joining and placing of Leaders is a very essential part of fireworks, as it is on the leaders, that the performance of all complex works depend; for which reason I shall endeavour here to explain the method of conducting pipes of communication, in as plain a manner as possible. Your works being ready to be cloathed, proceed thus; cut your pipes of a sufficient length to reach from one case to the other, then put in the quick match, which must always be made to go in very easy; when the match is in, cut it off within about an inch of the end of the pipe, and let it project as much at the other end; then fasten the pipe to the mouth of each case with a pin, and put the loose ends of the match into the mouths of the cases, with a little meal powder; this being done to all the cases, paste over the mouth of each two or three bits of paper; the preceding method is used for large cases, and the following for small cases and illuminations; first thread a long pipe, then lay it on the tops of the cases, and cut a bit off the under side, exactly over the mouth of each case, so that the match may appear; then pin the pipe to every other case, but before you put on the pipes, put a little meal powder in the mouth of each case; if the cases thus cloathed be port-fires on illuminated works, cover the mouth of each case with a single paper; but if they are choaked cases, situated so that a number of sparks from other works may fall on them before they are fired, secure them with three or four papers, which must be pasted on very smooth, that there may be no creases for the sparks to lodge in, which often set fire to the works before their time; avoid, as much as possible, placing the leaders too near together, or one across the other so as to touch, as it sometimes happens that the flash of one will fire the other; therefore if your works should be so formed, that the leaders must cross or touch, be sure to make them very strong, and secure them well at the joints and at every opening.
When a great length of pipe is required, it must be made by joining several pipes together, in this manner; having put on one length of match as many pipes as it will hold, paste paper over every joint; but if a still greater length be required, more pipes must be joined, by cutting off about an inch of one side of each pipe near the end, and laying the quick match together, and tieing them fast with small twine; after which, cover the joining with pasted paper.
The manner of placing Fireworks to be exhibited, with the order of Firing.
Nothing adds more to the appearance of fireworks, than the placing them properly; though the manner of placing them chiefly depends on the judgment of the maker. I shall give such rules here, as have been generally observed; for example, whether your works are to be fired on a building, or on stands; if they are a double set, place one wheel of a sort on each side of the building, and next to each of them towards the center, place a fixed piece, then wheels, and so on, leaving a sufficient distance between them, for the fire to play from one without burning the other; having fixed some of your works thus in front, place the rest behind them, in the center of their intervals; the largest piece, which is generally a regulated or transparent piece, must be placed in the center of the building, and behind it a sun, which must always stand above all the other works: a little before the building or stands place your large gerbes, and at the back of the works, fix your marron batteries, pots des aigrettes, pots des brins, pots des saucissons, air ballóóns, and flights of rockets; the rocket stands may be fixed behind or any where else, so as not to be in the way of the works.
Single collections are fired on stands, which stands are made in the same manner as theodolite stands, only the top part must be long or short occasionally; these sort of stands may be fixed up very soon without much trouble. Having given sufficient instructions for placing of fireworks, I shall proceed with the manner of firing them.
Order of Firing.
1. Two signal rockets, 2. Six sky rockets, 3. Two honorary rockets, 4. Four caduceus rockets, 5. Two vertical wheels illuminated, 6. Two spiral wheels illuminated, 7. Two transparent stars, 8. A line rocket of five changes, 9. Four tourbillons, 10. Two horizontal wheels, 11. Two air ballóóns illuminated, 12. Two Chinese fountains, 13. Two regulating pieces of four mutations each, 14. Two pots des aigrettes, 15. Three large gerbes, 16. A flight of rockets, 17. Two ballóón wheels, 18. Two cascades of brilliant fire, 19. Twelve sky rockets, 20. Two illuminated yew-trees, 21. Two air ballóóns of serpents, and two compound, 22. Four tourbillons, 23. Two Fruiloni Wheels, 24. Two Illuminated Globes with Horizontal Wheels, 25. One Pot des Saucissons, 26. Two Plural Wheels, 27. A Marron Battery, 28. Two Chandeliers Illuminated, 29. A Range of Pots des Brins, 30. Twelve Sky Rockets, 31. Two Yew-Trees of Fire, 32. A Nest of Serpents, 33. Two Double Cones Illuminated, 34. A Regulating Piece of Seven Mutations, viz., 1. A Vertical Wheel Illuminated, 2. A Golden Glory, 3. An Octagon Vertical Wheel, 4. Porcupines Quills, 5. Cross Fires, 6. A Star Piece with Brilliant Rays, 7. Six Vertical Wheels, 35. A Brilliant Sun, 36. A Large Flight of Rockets.
When water-works are to be exhibited, divide them into several sets, and fire one set after every fifth or sixth change of land and air-works; and observe this rule in firing in a double set of works, always to begin with sky-rockets, then two moveable pieces, then two fix’d pieces, and so on, ending with a large flight of rockets, or a marron battery; if a single collection, fire a fixed piece after every wheel or two, and now and then some air and water-works.
Fountain of Sky-Rockets.
Plate 6th. Fig. 1st, represents a fountain of thirty rockets; let A, be a perpendicular post, sixteen feet high from the ground, and four inches square. Let the rail or cross piece C, be one foot six inches in length, three inches broad, and one thick. The rail D, at bottom, must be six feet in length, one foot broad, and an inch thick. F, and G, are the two sides which serve to supply the rails D, E, H, I, C; these sides are one foot broad at bottom, and cut in the front with a regular slope, to three inches at top, but their back edges must be parallel with the front of the pots A. The breadth of the rails E, H, I, will be determined by the breadth of the sides; all the rails must be fixed at two feet distance from each other, and at right angles with the pots; having placed the rails thus; bore in the bottom rail, ten holes at equal distances from each other, large enough to receive easily the stick of a one pound rocket; in the back edge of this rail cut a groove from one end to the other, fit to contain a quick-match, then cut a groove in the top of the rail, from the edge of each hole, into the groove in the back; in the same manner cut in the second rail E, eight holes and grooves; in the third rail H, six holes and grooves; in the fourth rail I, four holes and grooves; and in the top rail two holes and grooves; B, a rail with holes in it to guide the ends of the rocket sticks, this rail must be fixed six feet from the rail D; the fountain frame being thus made, prepare your rockets thus; tie round the mouth of each a piece of thin paper, large enough to go twice round, and to project about an inch and a half from the mouth of the rocket, which must be rubbed with wet meal-powder; in the mouth of each Rocket put a leader, which secure well with the paper that projects from the mouth of the case; these leaders must be carried into the grooves in the back of the rails, in which lay a quick-match from one end to the other, and cover it with pasted paper; holes must be made in the rail D, to receive the ends of the sticks of the rockets, in the rail E, and so on to the fourth rail, so that the sticks of the rockets at top, will go through all the rails; the rockets being so prepared, fix a gerbe or white flower-pot on each rail before the post, with their mouths inclining a little forwards; these gerbes must be lighted all at once; behind or before each gerbe, fix a case of brilliant or slow fire, these cases must be filled so that they may burn out one after the other, to regulate the fountain, which may be done by carrying a leader, from the end of each slow or brilliant fire, into the groove in the back of each rail; different size rockets may be used in these fountains, but it will be best to fill the heads of the rockets on each rail with different sorts of things, in this manner, those at top with crackers, the next with rains, the third with serpents, the fourth with tailed stars, and the last flight with common or brilliant stars.
Palm-Tree.
This piece, though made of common fires, and of a simple construction, has a very pleasing effect; owing to the fires intersecting so often, that they resemble the branches of trees. Fig. 2d. let A, be a perpendicular post of any thickness so that it be sufficiently strong to hold the cases; let the distance from B to C, be two feet six inches, and from C to D, two feet six inches, and let the length of each cross piece be two feet; on each end of each, fix a five pointed star, then fix on pegs made on purpose, twelve inch half pound cases of brilliant fire, as in the figure, all the cases and stars, must be fired at one time; this piece should be fixed high from the ground.
Illuminated Pyramid, with Archimedian Screws, a Globe and Vertical Sun.
May be made of any size; one made according to the Dimensions of fig. 3d, will be a good proportion, whose whole height is twenty one feet; from C to D, six feet, from E to F, nine feet, the space between the rails must be six inches, and the rails as thin as possible, in all the rails stick port-fires at four inches distance; the archimedian screws G, K, are nothing more than double spiral wheels, with the cases placed on their wheels horizontally instead of obliquely, the vertical sun I, need not consist of more than twelve rays, to form a single glory; the globe at top must be made in proportion to the pyramid, which being prepared according to the preceding directions, place your leaders so that all the illuminating port-fires, screws, globe, and sun, may take fire together; the pyramid must be supported by the two sides, and by a support brought from a pole, which must be placed two feet from the back of the pyramid, in order that the wheels may run free.
Rose-Piece and Sun.
A rose piece may be used for a mutation of a regulated piece, or fired by itself, this piece makes the best appearance when made large; if its exterior diameter be six feet it will be a good size; fig. 4, shews the manner it appears before it is fired; let the exterior fell be made of wood, and supported by four wooden spokes, all the other parts on which the illuminations are fixed, must be made of strong iron wire; on the exterior fell, place as many half pound cases of brilliant charge as you think proper (but the more the better) for the nearer the cases are placed, the stronger will be the rays of the Sun; the illuminations should be placed within three inches of each other, they must be all fired together and burn some time before the sun is lighted, which may be done by carrying a leader from the middle of one of the illuminations, to the mouth of one of the sun cases.
Transparent Stars with Illuminated Rays.
Plate 7, Fig. 5th, represents an illuminated star, let the diameter from A to B, be two feet and from C to D, seven feet; first make a strong circular back or body of the star, two feet diameter, to which you fix the illuminated rays; in the center of the front of the body fix a spindle, on which put a double triangular wheel, six inches diameter, clothed with two ounce cases of brilliant charge; the cases on this wheel must burn but one at a time; round the edge of the body nail a hoop made of thin wood or tin, this hoop must project in front six or seven inches; in this hoop cut three or four holes to let out the smoke from the wheel; the star and garter may be cut out of strong paste-board or tin, made in this manner, cut a round piece of paste-board or tin, two feet diameter, on which draw a star, and cut it out, then over the vacancy paste Persian silk; paint the letters yellow; four of the rays yellow, and four red; the cross in the middle may be painted half red, and half yellow, or yellow and blue; this transparent star must be fastened to the wooden hoop by a screw, to take off and on, the illuminated rays are made of thin wood, with tin sockets fixed on their sides within four inches of each other; in these sockets stick illuminating port-fires; behind the point of each ray, fix a half pound case of grey, black, or chinese fire.
* * * * *
N. B. The illuminated rays to be lighted at the same time as the triangular wheel, or after it is burnt out, which may be done by a tin barrel being fixed to the wheel after the manner of those in the regulated pieces, into this barrel correl a leader from the illuminated rays, through the back of the star, which leader must be met by another brought from the tail of the last case on the wheel.
Transparent Table Star Illuminated.
Fig. 6th, represents a table star, whose diameter from E to F, is twelve feet, and from E to I, four feet, this proportion observed on each side, will make the center frame four feet square, in this square fix a transparent star, as shewn in the figure; this star may be painted blue, and its rays made as those of the flaming stars described in page 218, the wheel for this star may be composed of different coloured fires, with a change or two of slow fire; the wheels a, a, a, a, may be clothed with any number of cases, so that the star wheel consists of the same; the illuminating port fires, which must be placed very near each other on the frames, must be so managed as to burn as long as the wheels, and lighted at the time.
The Regulated Illuminated Spirili Piece, with a projected Star Wheel Illuminated.
This piece is represented by Fig. 7th, and is thus made; have a block made eight inches diameter, in this block screw six iron spokes, which must serve for spindles for the spiral wheels, these wheels are made as usual, each one foot six inches diameter and three foot in height; the spindles must be long enough to keep the wheels four or five inches from one another; at the end of each spindle must be a screw nut, on which the wheels that hang downwards will run, and on the spindles which stand upwards must be a shoulder, for the blocks of the wheels to run on.
* * * * *
The projected star wheel, must turn on the same spindle on which the large block is fixed, this spindle must be long enough to allow the star wheel to project a little before the spiral wheels; the exterior diameter of the star wheel, must be three feet five inches, on this wheel fix three circles of iron wire, and on them port-fires; on the block place a transparent star, or a large five pointed brilliant star, the cases on this wheel may burn four at once, as it will contain near twice the number of one of the spiral wheels; the cases on the spiral wheels, must be placed parallel to their fells, and burn two at a time.
A New Figure Piece Illuminated with Five Pointed Stars.